1911 Firearm Addicts banner
trigger
1-20 of 71 Results
  1. 1911 Gunsmithing
    I am trying to get some measurements on a couple of items. I dont have these, and just doing some dream/planning. What are the widths of the magazines for the following Double stacks, the Caspian, the 2011, and the Glock 21? What is the inner width of the trigger bow of the Caspian and the...
  2. 1911 Gunsmithing
    I wouldn't call this a trigger job --as it started out as a trigger swap -- but I did polish the bows with 800 grit Scotchbrite and then finished the sides and rear of the trigger bow in Flitz, it was like polished glass. Then I addressed the part of the disconnector the rests on the rear of the...
  3. General 1911 talk
    I have a Ruger SR1911 Target Model. I like everything about it a lot. My only complaint is the trigger could be better. It’s light enough; it just doesn’t have a crisp break. I don’t want a trigger job. I’m wondering if an aftermarket trigger could give me that glass rod I’d like. If so, what...
  4. General 1911 talk
    I hate to admit this, but before yesterday I had never fully taken down a Series 80 gun before. Half of this is due to my LACK of Series 80's guns, the other half was from the fear and trepidation of the thought of trying to get all those extra bits and pieces put back together properly. I...
  5. General 1911 talk
    Stupid question / poll of the day. It's sure to create some controversy. When installing a trigger overtravel screw, do I run it in from the front, or draw in forward from the rear? What say you?
  6. General 1911 talk
    An alternate thread bestowing the virtues of a new members acquisition of a DW Guardian and his trigger laments wrought forth in me enough curiosity to exchange a trigger in one of mine. Both of these had stock Dan Wesson triggers yesterday. Now one is different. Trouble is, I don't really...
  7. Sold/Expired Classifieds
    Bought this cause I wanted to see one in hand. Personally it's a great idea and if I were starting over I'd put these in every 1911 I own. I test fit it in Colt, LB, and DW...the pins line up perfectly in all those I tested. Asking $200.00 shipped, that's a Franklin off retail. Or I would trade...
  8. 1911 Gunsmithing
    It's very simple actually. Here they are . . . . . . This . . . . . . . . . and this . . . . . Okay, so I need to know how you guys adjust these pre-travel tabs on YOUR triggers without turning the trigger bow into a pretzel. My needle nose pliers jaws are a little wider that that...
  9. General 1911 talk
    I'd like to send the gun off with some newer parts, it's been sitting around unfired for a long time. Sight set, 10-8 makes a heftier rear sight that will fit the Government cut, leaning that direction. Would like to have a fiber optic front sight which will require a cut, not a problem, but...
  10. General 1911 talk
    So, I've got a Springfield LB Operator and I think it needs a trigger job. Or at least I feel like it needs to be improved for me to be happy with it. I'm almost at 1000 rounds (easily twice that in dry fire) and I'm thinking it's not going to get any better than it is right now. The gun has a...
  11. General 1911 talk
    I've had several 1911 pistols over the past 15 years.. I'm going to build out my next one this winter and wanted to hear opinions on running a flat trigger, I've shot a few but never took the time to notice the nuances of the design. I'm going to add some 10-8 goodies to this build and they...
  12. Autoloaders
    So I still haven't been able to get to the range with my new to me CZ 75D PCR, but I have been dry firing it a fair bit. Had some time yesterday, so I figured it was time we got a little better acquainted. Didn't do a detail strip, but I did get it squeaky clean, then lubed it pretty...
  13. 1911 Gunsmithing
    I was crowing a bit about how well everything went with the installation of my new C&S trigger kit, prior to actually test firing it. Or should I say, attempted to test fire it :oops:. Got the dreaded click instead of a bang, and not a mark on the primers. Figured it was the S80 parts, for...
  14. General Firearm Discussion
    I bought a fantastic(customized) SA Range officer-Operator model. 9mm. love the gun. The work done made it a real keeper. it is very accurate .. That said, for whatever reason, I hit my shots 2" low most of the time. When I get a shot to hit poa=poi I find that it is a very specific...
  15. General 1911 talk
    Ok gent's...I NEED SOME HELP HERE....I cross-posted this in the gunsmithing section also.... So I took my steadfast & trusty STI Trojan .45acp to the range today to run the May drill. I did a quick warm up...10 round slow fire...no issues, gun was laser accurate as usual. New G10 grips felt...
  16. General 1911 talk
    Hey all, so i have a sweet Fusion 1911 in .45acp. I noticed something today when I was doing a little dry-firing..... When I pull the trigger and the shot breaks, while holding the trigger back I rack the slide in order to release out to reset...BUT the trigger shoe "jumps"/"Clicks" back a...
  17. Autoloaders
    So, I ran a Glock for years...both in competition (USPSA) and as a duty and off-duty weapon. As such, I've also been on the hunt for the "perfect" trigger. - I started with the stock trigger, and learned how to shoot to reset. - I then did the .25 cent polish job and it smoothed things up...
  18. Sold/Expired Classifieds
    This is brand new, installed and function tested. Huge improvement over the stock trigger pack. There is a slight dent from shipping - this is how I received it from Brownells. This is cosmetic. $250 (shipped) or best offer - comes with paperwork, & oil. Might trade for optic, 1911 stuff, or ...
  19. General Firearm Discussion
    Hey all, I'd like to get some suggestions from you guys and gals out there that have upgraded the trigger in your Glock pistols. I'd like to get a better trigger for my G19, which is stock, but I don't want to spend $150 to do it. There has to be alternatives available to improve the Glock...
  20. 1911 Gunsmithing
    Anyone know where I can get one? Thanks in advance. Z
1-20 of 71 Results
Top