1911 Firearm Addicts banner

1 - 20 of 22 Posts

·
John 14:6
Joined
·
1,462 Posts
Discussion Starter #1 (Edited)
Good day gents,

I bought this pistol from [email protected], he purchased it from Sterling Archer. I only fired 50 rounds through it an put it in the safe. A brother gunner saw it liked it and I sold it to him. He never fired a round through it.

Dean has fallen on hard times with medical bills and is facing Chapter 13. I am listing this pistol on his behalf. No monies will come to me if purchased but will go directly to Dean. I will PM you with the information to send the funds. When they clear the gun will ship from FFL to FFL.

The gun is as follows described by Sterling Archer is the original listing. The pictures I took a short time ago and are current. Some of the listings of parts etc are from the original post and have been edited appropriately. This is a smoking deal!! On to the good part!!

IMG_20190420_142005052.jpg

IMG_20190420_141916558.jpg

IMG_20190420_142303998.jpg

IMG_20190420_141951274.jpg

View attachment 256001
IMG_20190420_140543610_HDR.jpg

Dan Wesson Custom Shop CCO .45
Stainless steel Commander slide
Stainless steel Officer frame <-- Steel frame, not aluminum.
Ball cuts
25 LPI front strap
Undercut trigger guard
Phase II dehorn
Flush cut and reverse crown barrel
Plain black ledge rear sight
Tritium front sight
Recessed slide stop
Short trigger
3.75# trigger pull
EGW Carry Bevel bushing
EGW flat-wire .250 guide rod and spring plug
ISMI Commander flat-wire recoil spring
Wilson Bullet-Proof wide Ambi thumb safety trimmed right side lever
Wilson Bullet-Proof slide stop
Wilson Bullet-Proof Tactical mag release
Smith and Alexander arched mag well
VZ Operator II grips (Beveled and Cerakoted)

Magwell/MSH
You don't often see a mag well on a compact frame but I encourage you to try it. It only adds .25" in height but makes a big difference in feel. If you prefer no magwell or no arch a simple swap and you're set.

Derr Precision work-
Blend mag well
Line up ball cuts
Bevel bottom edge of the slide
French Borders
Beavertail knuckle relief notches (Pictured below)
Beavertail high grip mod
Reduce and blend thumb safety panels
Wilson Bullet-Proof extractor, plus spare
New EGW Carry Bevel bushing, hand-fit for optimum accuracy
Greg Derr Cerakoted it Graphite Black. after learning that stainless steel and I don't get along. If Cerakote isn't to your liking bead blast it down to the original stainless gun.

1 - Tuned WC SS Bullet-Proof spare extractor
2 - Tuned DW spare extractors
1 - DW factory EGW Carry Bevel bushing, finger tight
2 - DW 7-round factory mags
2 - Wilson 8-round mags
3 - Tripp 7R-45-RO
2 - ISMI 22# Flat-wire Commander Recoil Spring
1 - ISMI 20# Flat-wire Commander Recoil Spring
1 - ISMI 18# Flat-wire Commander Recoil Spring
1 - 22# Wolff Conventional Recoil Spring
1 - 18# Wolff Conventional Recoil Spring
3 - Wolff Firing Pin Springs, Standard Power
3 - Wolff 23# Officer Hammer Springs
1- Wolff 22# Officer Hammer Spring
1- Wolff 21# Officer Hammer Spring
1- Wolff 20# Officer Hammer Spring
Everything is above board! Rest assured that what you see is what you get.

Sterling invested $3500 into this gun.
The price is $1800 shipped and insured. USPSMO or Certified/Teller Bank check.
First I'll take it followed by a PM to me gets it!


Thank you for looking and considering this gun.
Greg
PS: This listing is cross-posted. If there is a problem with me listing this gun for Dean please advise me. Thank you in advance.
 

·
John 14:6
Joined
·
1,462 Posts
Discussion Starter #4
If this had been for sale a week (and pistol) ago...
I get it. Just found out yesterday and picked it up today for photos etc. This is a really nice gun and a smoking deal. If I didn't have a gun from Karl coming soon I just would have bought it back.
 
  • Like
Reactions: Haroldg48

·
Registered
Joined
·
2,866 Posts
PM sent
 

·
Registered
Joined
·
1,018 Posts
I get it. Just found out yesterday and picked it up today for photos etc. This is a really nice gun and a smoking deal. If I didn't have a gun from Karl coming soon I just would have bought it back.
Well, you COULD sell ME that LW that Karl built for you and then you could buy this one!

Problem solved! :smurggrin:
 

·
John 14:6
Joined
·
1,462 Posts
Discussion Starter #12
Not happening, Bro!!!
Heck, I don't even have it in hand to fondle. ;)
 
  • Like
Reactions: Karl Beining

·
Registered
Joined
·
6,069 Posts
This is a smoking deal! Even though I have too many irons in the fire, I would totally snap this up if it was on the roster. Best wishes for Dean.
 

·
John 14:6
Joined
·
1,462 Posts
Discussion Starter #19
Full disclosure. This is now cross-posted on another forum.
 
1 - 20 of 22 Posts
Top